-
Buyers
18142 --- 7-Way Flat Pin to 4-Prong Flat Adapter
Does your vehicle have a 7-Way Flat Pin Socket and your trailer have a 4-Prong Flat Connector? This adapter is your answer. It converts the vehicle's 7-Way Flat Pin Socket to a 4-Prong Flat Female Connector. Simply plug the adapter in to the 7-Way Socket...$6.95 -
Demco
05408X --- Demco 3/32" Cable with Hook - 42-1/2"
Yoke on one end for hooking to the brake actuator emergency lever and a 3/8" safety clip hook on the other end. Over All Length: 42 1/2" 3/8" Hook with Safety Clip not a Replaceable Item Fits DA91, DA91BZ, DA10 and DA20 Brake Actuators Demco has...$14.45 -
Buyers
B58 --- 5/8" Bent Pin and Hair Pin Set
Can be used with most square shank adapters and ball mounts. Tapered end for easy installation Shaft Size: 5/8" 3" of usable length Finish: Zinc Fits 2" Receivers$4.45 -
$5.45
-
Croft
HV-3 --- CROFT Coupler Repair Kit for CROFT Couplers with Loop Nuts
Loop Nut Repair Kit for Croft Couplers includes one each of the following: Bolt 5/8" - 11 X 4", 2-3/4" Thread Length - Part No. B-3 Tension Washer - Part No. W-3 Spring - Part No. S-3 Lip-High Grade Cast Steel - Part No. C-3 Loop Nut, 5/8" - 11 thread -...$19.95 -
Buyers
74149 --- 5/8" Bent Pin and Hair Pin Set
Can be used with most square shank adapters and ball mounts. Tapered end for easy installation 3.816" of usable length Finish: Zinc Plated Yellow Fits 2", 2-1/2" and 3" Receivers$5.45 -
SpanSet
HD-15FTJ --- Heavy Duty Tie Down Strap with Ratchet - J Hook End Fittings - 2" x 15'
Working Load Limit: 3,335 lb Length: 15’ Width: 2" End Fittings: J Hooks Heavy Duty Tie Down Strap Break Strength: 10,000 lb$25.95 -
Tow Ready
4PFC-60 --- 4-Prong Flat Vehicle and Trailer Ends - 60"
Black Molded plastic with 16 ga. wire. Trailer End = Male Half Vehicle End = Female Half AOL: 60"$10.95 -
$3.95
-
Tekonsha
2010 --- Tekonsha Breakaway Switch
Breakaway Switch Nylon Pull Pin will not Freeze Up Corrosion Free Silver Contact Points Weldable Metal Tab Reinforced Nylon Case$20.95 -
Croft
BO48-A --- Croft Bolt On Saddle with Ring
A CROFT Original. This Saddle is Tough, Durable and Rugged. It is made to Bolt On to a 3" tongue. Bolt on Saddle with Ring Capacity: 5,000 lb Class 3 Rating Ring Thickness: 1" Ring Inner Diameter: 2-1/2" Mounting: Bolt onto 3" wide trailer tongue...$59.95 -
Croft
N-3 --- Loop Nut for Croft Couplers
Loop Nut 5/8" - 11 Threads per Inch Loop Nut 5/8" - 11 Threads per Inch Zinc Plated$6.95 -
Draw-Tite®
63845 --- 2" Hitch Ball, 7,500 lb Capacity, Chrome Finish
2" Chrome Hitch Ball Chrome Finish 7,500 lb Capacity A: 2" Hitch Ball B: 1" Shank Diameter C: 2-1/8" Shank Length Drawbar Thickness Range: 3/8"-3/4" Includes Wrench Flats$15.95 -
Croft
AH3 --- CROFT Adjustable Coupler with N-3 Loop Nut - 7,000lb Capacity - 2"
The CROFT Original. Adjustable couplers offer the flexibility of changing the coupler height to match multiple towing vehicles. This adjustable coupler is safe, rugged and simple to operate. Its body and lip are constructed of high grade cast steel and...$103.95 -
Tekonsha
118044 --- 4-Prong Flat Vehicle and Trailer Ends
Black Molded plastic with 16 ga. wire. Trailer End = Male Half Vehicle End = Female Half Length: 48"$11.45 -
Buyers
DRING-334 --- D-Ring -3/4" Ring Diameter
The heavy duty D-Ring is forged from C-1045 steel with 3/4" thick diameter ring. The forged steel mounting bracket is 2-1/4" wide and 3/8" thick. Working Load Limit: 9,120 lb Mounting Bracket Dimensions: 2-1/4" wide and 3/8" thick Forged Steel...$15.95 -
Optronics
142-49 --- Replacement 2-Wire Plug
Replacement 2-Wire Plug for series 142, 143, 145, 146, and 150 clearance and marker lights, and all competitive models Includes 6" Ground Wire with #10 Ring Terminal and Hot Wire Style: 2-Wire Molded Plug Brand: Peterson # B142-49 Fits the...$1.45 -
Croft
AR1 --- Croft Adjustable 2-1/2" Tow Ring - 12,000 lb Capacity
Our very own Class IV tow ring made from high grade cast steel. This rugged and reliable tow ring is zinc plated and has an inner diameter of 2-1/2". The ring thickness diameter is 1-1/4". Capacity: 12,000 lb Vertical Load: 1,200 lb Simple, Safe,...$37.95 -
Croft
B-3 --- Replacement Bolt for Croft Couplers
Bolt 5/8" - 11 x 4" Bolt 5/8" - 11 x 4" Zinc Plated 2-3/4" Thread Length 7/8" Square Head on Bolt$3.45 -
Peterson
440 --- Square Combination Right Tail Light - For Under 80" Wide Trailer
This under 80" Combination light has all the features you need for the right hand light. Square Right Light Color: Red Functions as Stop, Turn, and Tail Light, Rear Reflex, Side Marker and Side Reflex Depth: 2-7/8" Length: 5" Height:...$9.45 -
Peterson
440L --- Square Combination Left Tail Light - For Under 80" Wide Trailer
This under 80" Combination light has all the features you need for the left hand light. Square Left Light Color: Red Functions as Stop, Turn, and Tail Light, Rear Reflex, Side Marker, Side Reflex, and License Light Length: 5" Height:...$9.95 -
Tekonsha
2010A --- Replacement Cable and Pin for 2010 Tekonsha Breakaway Switch
Use on Tekonsha 2010 Breakaway SwitchUse on Tekonsha 2010 Breakaway Switch$9.45 -
Buyers
58102 --- Receiver Adapter, 2-1/2" to 2"
The receiver adapter is perfect for cargo carriers and bike racks. Receiver Adapter, 2-1/2" to 2" use with 5/8" pin$23.95 -
Demco
12426 --- Demco & DexMarine Damper Shock
This Damper Shock fits the following Brake Actuators: Demco DA10 - Two Required Demco DA20 - Two Required Demco DA91 - One Required Demco DA91BZ - One Required DexMarine DX8.0 (Dico/Titan Model 6) - One Required DexMarine DX12.5 (Dico/Titan Model...$44.95 -
Demco
05680X --- Demco Drum Brake Master Cylinder Kit w/Gasket
Replacement Master Cylinder for Demco Brake Actuators. For Use with Drum Brakes Only. Fits only Demco brake actuators For use with Drum Brakes Only Kit includes mounting hardware, gasket, cap, rubber boot and cover plate Diaphragm in master...$62.95 -
Demco
12200 --- Demco 3/32" Cable with Hook - 31"
Yoke on one end for hooking to the brake actuator emergency lever and a 3/8" safety clip hook on the other end. Overall Length: 31" 3/8" Hook with Safety Clip not a Replaceable Item 3/32" Diameter Cable Includes mounting hardware, nut and...$10.45 -
Buyers
RMPH200B --- Receiver Mount Pintle Hook Combination with 2" Hitch Ball
This combination pintle hook and hitch ball gives you the flexibility of towing with either pintle hook/tow ring or hitch ball/coupler. The durable black powder coat finish resists corrosion. Fits Standard 2" Receiver Pintle Capacity: 12,000...$115.95 -
Buyers
LP716 --- Tailgate Lynch Pin - 7/16"
Lynch Pin Pin Length: 1-1/4" Ideal Use for Trailer Tailgate Securement Finish: Yellow Zinc Plated Pin Diameter: 7/16"$1.95 -
RAM
RAM2BWC --- RAM Adjustable Coupler - 7,000 lb Capacity - 2"
These sleeve Lock couplers come with a precision angle shaped self adjusting cast head for easy hooking and unhooking. Adjustable couplers include grade 8 bolts and nuts and work with industry standard 3" channel. Sleeve Lock couplers come with black...$49.95 -
SpanSet
HD-15FT --- Heavy Duty Tie Down Strap with Ratchet - Flat Hook End Fittings - 2" x 15'
Working Load Limit: 3,335 lb Length: 15’ Width: 2" End Fittings: Flat Hooks Heavy Duty Tie Down Strap Break Strength: 10,000 lb$26.95 -
CargoSmart
CS1705 --- Large Flat Hook for X-Track/E-Track Systems
Large Flat Hook Designed to fit on E-Track or X-Track.200 lb safe workloadZinc PlatedFlat Bottom Hook DesignIdeal for Holding Ladders and Other Large Cargo$5.95 -
Buyers
LP516 --- Tailgate Lynch Pin - 5/16"
Lynch Pin Pin Length: 1-1/4" Ideal Use for Trailer Tailgate Securement Finish: Yellow Zinc Plated Pin Diameter: 5/16"$1.45 -
RAM
DRING-3 --- D-Ring - 5/8" Ring Diameter
The heavy duty D-Ring is forged from C-1045 steel with 5/8" thick diameter ring. The forged steel mounting bracket is 2-1/2" wide and 3/8" thick. Mounting Bracket Dimensions: 2-1/2" wide and 3/8" thick Inner Dimension of Ring: 3" x 3" Working Load...$8.95 -
RAM
PSC27716 --- 1/4" Proof Coil Safety Chain - 27" Length
Safety Chain Finish: Zinc Working Load Limit: 1,730 lb Capacity: 5,200 lb 7/16" S-Hook w/Clip on One End Chain Length: 27" Link Size: 1/4" 1/4" Proof Coil Safety Chain Warning: Chains are NOT designed or approved for overhead lifting$8.45 -
Demco
12427 --- Nylon Wear Button .075" Thick - DX12.5 (Model 10)
Nylon Wear Button - DX12.5 (Model 10) Quantity Required Per DexMarine DX12.5 Actuator: 8 For use on the Sides of the Inner Slide, 4 per side Thickness: .075" Legacy Brand: Dico/Titan Model 10$0.93 -
Buyers
18143 --- 6-Way Round to 4-Prong Flat Adapter
Does your vehicle have a 6-Way Round Socket and your trailer have a 4-Prong Flat Connector? This adapter is your answer. It converts the vehicle's 6-Way Round Socket to a 4-Prong Flat Female Connector. Simply plug the adapter in to the 6-Way Socket and...$4.95 -
RAM
700263 --- Replacement 9/16" Drop Leg Pin, Chain and Lynch Pin
Drop Leg Pin Diameter: 9/16" Overall Length: 4-7/8" Usable Length: 3-3/4" Includes Lynch Pin to secure 9/16" Pin Drop Leg Pin Diameter: 9/16" Overall Length: 4-7/8" Usable Length: 3-3/4" Includes Lynch Pin to secure 9/16" Pin$11.45 -
RAM
SC3614CH --- 1/4" Transport Safety Chain - 36" Length
Safety Chain Finish: Yellow Zinc Working Load Limit: 4,200 lb Capacity: 12,600 lb 1/4" Clevis Slip Hook on One End Chain Length: 36" Link Size: 1/4" 1/4" Transport Safety Chain Meets J684.6.3.4 SAE Requirements Warning: Chains are NOT designed or...$10.45 -
RAM
RAM158451 --- RAM Swivel TopwindTrailer Jack - 2,000 lb
This RAM jack swivels into four different positions by pulling an easy grip pin. Maximum Support Capacity: 3,000 lb Maximum Lift Capacity: 2,000 lb Handle Style: Topwind Travel: 10" Retracted Height: 11.25" (Measured from Center of Mounting Bracket)...$46.95 -
Draw-Tite®
63847 --- 2-5/16" Hitch Ball, 7,500 lb Capacity, Chrome Finish
2-5/16" Hitch Ball Chrome Finish 7,500 lb Capacity A: 2-5/16" Hitch Ball B: 1" Shank Diameter C: 2-1/8" Shank Length Drawbar Thickness Range: 3/8"-3/4" Includes Wrench Flats$21.95 -
Croft
C-3 --- Replacement Lip for Croft Couplers
Lip-High Grade Cast Steel Lip-High Grade Cast Steel Zinc Plated$9.95 -
Dexter Marine
10209 --- Nylon Wear Button - DX8.0 (Model 6) & DX12.5 (Model 10)
Nylon Wear Button - DX8.0 (Model 6) & DX12.5 (Model 10) Quantity Required For DexMarine DX8.0 (Model 6) Actuator: 2 Quantity Required For DexMarine DX12.5 (Model 10): 6 Nylon Wear Button Thickness: .125" Legacy Brand: Dico/Titan Model 6 &...$2.95 -
Dexter
WN91618 --- Wheel Nut 9/16" - 18 Right Hand
Wheel Nut - Lug Nut9/16" - 18 Right Hand Thread7/8 Inches Across FlatsZinc Plated60 Degree Cone$1.95 -
Dexter
DIS7262 --- Knurled Drive-In Stud - 1/2"
Drive-In Stud Thread Diameter (A): 1/2" Stud Length (B): 2-5/8" Spline Length (C): .93" Base Length (D): 1.38" Spline Diameter (E): .54"$2.95 -
Hopkins
20051 --- TAP® Replacement Engager™ Break-Away Pin & Cable
Replacement Pin Overall Pin Length: 1-5/8" Pin Dimension: 7/16" tall x 3/16" wide Replacement Pin & Cable for 20010 & 20050 Break-Away Switch Hoppy / Tap Model #20051$6.95 -
Buyers
B2426FS --- Formed Hinge Strap with Grease Fitting
Formed Hinge Strap Formed Hinge Strap with Grease Fitting Formed .31" thick steel hinge Includes zinc washer, hex head cap screw and Lockout, plastic bushing 1/2" bolt Strap Height: 2.25" 3.85" L x 4.33" W x 2.44" T$14.95 -
Draw-Tite®
40343 --- Ball Mount Long Shank - 2" Drop - 6,000 lb Capacity
Reversible Ball Mount for high or low ball height (rise or drop). Ball Mount fits standard 2" Receivers Ball Mount provides 2" Drop from the top of the shank to the top of the ball platform Ball Mount provides 3/4" Rise from the top of the shank to the...$31.95 -
Buyers
TBM12-B --- Tri-Ball Combination for 2" Receivers with welded Black Hitch Balls
Never be without the ball size you need for the job. This Tri-Ball Mount Combination has them all, 1-7/8", 2", and 2-5/16" Hitch Balls welded onto a 2" shank. Ball Mount fits standard 2" Receivers Hollow Shank Dual 5/8" Hitch Pin holes 1-7/8" Hitch Ball...$65.95 -
Peterson
LED421KR7 --- Oval Sealed LED Tail Light Kit- 7 Diodes
LEDs (Light Emitting Diodes) are devices that have no moving parts, no bulbs that burn out or break, and have no toxic gasses. LED devices do provide longer lasting performance, are more energy efficient, require lower voltages to operate, and increase...$18.95 -
Buyers
4666 --- 1/2" Bent Pin and Hair Pin Set
Can be used with most square shank adapters and ball mounts. Tapered end for easy installation Finish: Zinc Fits 1-1/4" Receivers$2.95 -
Peterson
426R --- Round 4" Sealed Tail Light - Red
This durable light has a polycarbonate lens that is welded to the housing to form single unit. 4" Round Sealed Light Color: Red Functions as Stop, Turn, and Tail Light Depth: 2-1/16" Diameter: 4" Made in the USA Required Mounting Grommet: 426-18...$9.45 -
Draw-Tite®
40342 --- Ball Mount - 2" Drop - 7,500 lb Capacity
Reversible Ball Mount for high or low ball height (rise or drop). Ball Mount provides 2" Drop from the top of the shank to the top of the ball platform Ball Mount provides 3/4" Rise from the top of the shank to the top of the ball platform Use with 1"...$27.95 -
Dexter
6-190 --- EZ Lube Washer (After 2002)
Fits One Inch Diameter EZ Lube Spindles Must be used with EZ Lube Jam Nut. Our Part Number 6-191 This Washer Snaps Over the EZ Lube Jam Nut$5.45 -
Buyers
CB25161-10K --- 2-5/16" Hitch Ball, 10,000 lb Capacity, Chrome Finish
2-5/16" Chrome Hitch Ball Chrome Finish 10,000 lb Capacity 2-3/4" Shank Length 1" Shank Diameter 2-5/16" Hitch Ball No Wrench Flats$21.95 -
Dexter
4632 --- Dexter Oil Cap Plug
Center Rubber Plug on Dexter Oil Caps Snaps into 7/8" Hole Fits Dexter 2135, 2188 and 2136 Oil Caps$3.45 -
$5.45
-
Demco
03876X --- Demco Master Cylinder Cap w/Diaphragm & O-Ring
Demco Replacement Master Cylinder Cap Fits the Demco models DA66, DA70, DA86, DA10, DA20, DA91BZ and DA91 Includes built in diaphragm Includes O-ring$19.95 -
Hydro-Act
1844-2 --- Hydro-Act Actuator Damper Shock
Quantity Required per Actuator: 1 Collapsed Length: 6.25" Center of Pin to Center of Pin Extended Length: 8.125" Center of Pin to Center of Pin 7/16" pinhole diameter on both sides of damper$179.95 -
Demco
1906 --- Wheel Cylinder Left Hand Assembly for 10" and 12" Hydraulic Brake
Left Hand Uniservo Wheel Cylinder Fits Uni-Servo and Free-backing Hydraulic Brakes 1-1/8" Bore Includes Push Rod and Bleeder Finish: Aluminum Mounting Bolts and Washers not included, Requires two of each: B5160625G5ZC and 12489$35.95 -
$0.95
-
Demco
1907 --- Wheel Cylinder Right Hand Assembly for 10" and 12" Hydraulic Brake
Right Hand Uniservo Wheel Cylinder Fits Uni-Servo and Free-backing Hydraulic Brakes 1-1/8" Bore Includes Push Rod and Bleeder Finish: Aluminum Mounting Bolts and Washers not included, Requires two of each: B5160625G5ZC and 12489$35.95 -
Buyers
10-160 --- 7-Terminal Junction Box
A junction box provides a single connection point for easy repair and replacement of trailer connectors. Includes cover, four grommets and two strain relief clamps Mounts on 7-3/4" Centers, 5/16" hole diameter Black, High impact poly box Can Be Wired...$10.95 -
Buyers
DPH2000 --- Pintle Hook Combination with 2" Hitch Ball - 16,000 lb Capacity
This strong and reliable drop forged pintle hook is combined with a forged steel ball. The hitch balls are interchangeable. The black powder coat finish is corrosion resistant. Ball Capacity: 10,000 lb Vertical Load: 3,000 lb Pintle Capacity: 16,000...$93.95 -
Hydro-Act
1829 --- Hydro-Act Actuator Shaft
Quantity Required per Actuator: 4 Over All Length: 5-3/8" For use on 5k-7k models Do not use on 12.5k models Requires two Lock nuts per shaft, part number: LN12G8ZF$29.95 -
Peterson
820012 --- Polycarbonate Document Holder
Stores licenses, permits and inspection stickers, keep them free of moisture and dirt. Includes Mounting Screws High-Impact Plastic Tension Spring holds Documents in Place with Cover Removed Cam-on Translucent Cover has Gasket Seal Polycarbonate Smoked...$13.45 -
18403 --- Replacement 9/16" Pin and Chain
Usable Length: 4" Overall Length: 4-1/2" Diameter: 9/16" Use with Mounting Tube, Part No. 15273$13.45 -
Croft
BOS/RING --- Croft Reversible Bolt On Saddle with Ring
A CROFT Original. This Saddle is Tough, Durable and Rugged. It is made to Bolt On to a 3" tongue. A 3" wide coupler can then be bolted onto the saddle. The saddle can then be easily switched from coupler to ring. Bolt on Saddle with Ring Capacity: 5,000...$65.95 -
Peterson
440-15R --- Peterson Replacement Red Square Lens
Peterson Replacement Lens for Part No. 440, 440L, 444, 444L, 452, 452L, 441 and 441L Combination Tail Lights Square Replacement lens Color: Red Length: 4-5/8" Height: 4-5/8" Attachment: 4 Screw Holes Screws included Brand: Peterson$3.95 -
Buyers
BML58 --- Trailer Hitch Receiver Lock for 2" and 2-1/2" Receivers
Protect your investment against drawbar and ball mount theft with this receiver Lock. It features a covered key slot preventing corrosion in the Locking mechanism. Tough, Rugged Construction Chrome Plated Pin Black Powder Coated Lock 5/8" Diameter Bent...$13.45 -
Croft
TJWK20-SFF --- Croft Flat-Free Wheel Kit with Swivel Feature
This flat-free wheel kit will allow you to move your single axle trailer tongue in any direction without binding. It will aid in getting a single axle trailer moved into just the right spot. This wheel kit is a popular item for man lifts. Includes...$182.95 -
Dexter
6-92-1 --- Flanged Lock Nut
Use this flanged Lock nut with the 007-126-00 shackle bolt. Flanged Lock Nut Finish: Zinc 7/16" - 20 Use with 007-126-00 Shackle Bolt$3.45 -
Buyers
TBM12P --- Tri-Ball Combination for 2" Receivers with Pintle Combo
Tri-Ball Mount with Pintle Hook Combination features 3 welded Towing Hitch Balls and a cast steel Pintle Hook on 1 Solid Steel Shank. Upper jaw Locks in the open (up) position for coupler towing with the 2" Hitch Ball. Upper jaw Locks in the closed...$130.95 -
Buyers
CB210K --- 2" Hitch Ball, 10,000 lb Capacity, Chrome Finish
2" Chrome Hitch Ball Chrome Finish 10,000 lb Capacity 2-3/4" Shank Length 1" Shank Diameter 14 threads per inch 2" Hitch Ball No Wrench Flats Point of Purchase Display Package$17.95 -
Hopkins
20400 --- TAP© Engager Break-Away Kit with LED Test Light - Front Mount
The Engager is designed to activate the trailer brakes in the event the trailer is separated from the towing vehicle. Trailer break-away kits are legally required in most states and Canada. The Engager is designed to be used with one or two axle trailers...$58.95 -
Buyers
18160 --- 7-Way Flat Pin to 6-Way Round Adapter
Does your vehicle have a 7-Way Flat Pin Socket and your trailer have a 6-Way Round Plug? This adapter is your answer. It converts the vehicle's 7-Way Flat Pin Socket to a 6-Way Round Socket. Simply plug the adapter in to the 7-Way Socket and you are...$6.45 -
Peterson
421KR --- Oval Sealed Tail Light Kit
This oval light may be used on either curbside or roadside of trailer and can be mounted horizontally or vertically. Kit includes light, grommet, and plug. Oval Sealed Light Kit Color: Red Functions as Stop, Turn, and Tail Light One kit includes...$15.95 -
Buyers
1802215 --- Ball Mount, Combination 2" and 2-5/16" Welded Hitch Balls, 10,000 lb Maximum Capacity
Ball Mount Combination with 2" Hitch Ball and 2-5/16" Hitch Ball welded onto a solid shank. Solid Shank Construction Ball Mount length is 8" from center of ball to center of pinhole 2-5/16" Hitch Ball Rating: 10,000 lb Gross Towing Weight, 1000 lb...$63.95 -
Buyers
RMPH2516B --- Receiver Mount Pintle Hook Combination with 2-5/16" Hitch Ball
This combination pintle hook and hitch ball gives you the flexibility of towing with either pintle hook/tow ring or hitch ball/coupler. The durable black powder coat finish resists corrosion. Pintle Capacity: 12,000 lb Vertical Load: 2,400 lb 2-5/16"...$126.95 -
Demco
03528X --- Removable 3-Point Strap for CROFT Tow Dolly
This durable nylon strap with wheel bonnet is designed to adjust to fit 13" to 15" tires. Two ends of the strap are fitted with a heavy duty 2" flat hooks and the other end fits into a 2" ratchet. Strap Adjusts to Fit Around 13" to Narrow 15" Tires...$36.95 -
Croft
TVTB03 --- Trailer and Vehicle Test Box - Lights, Electric Brakes, and Vehicle Connector
Croft Original! We designed this test box as an aid for testing trailer lights, electric brakes, and the vehicle connector. It allows one person to visually test brake lights, tail lights, right and left turn signal lights and electric brakes by simply...$399.95 -
Draw-Tite®
63057 --- 2" Receiver Mounted Pintle Hook Adapter - 8 Holes - 12,000 lb Capacity
Receiver Mount Pintle Hook Adapters provide mounting for both rigid type pintle hooks and dual purpose ball pintle hooks. Fits 2" Receiver Capacity: 12,000 lb Vertical Load: 1,200 lb Solid Shank Construction Shank Length (center of pinhole to...$95.95 -
Master Tow
MTFENDER --- Master Tow Dolly Fender - Right or Left Side
Master Tow Replacement Tow Dolly Fender Can be used on left or right side Color: Cream Width: 8" Length: 28-1/4" Height: 11-3/4" Covers that hold lights and bolts for covers are included Bolts for mounting fender to the dolly are not...$98.95 -
Dexter
007-126-00 --- Dry Shackle & Equalizer Center Bolt
This shackle bolt has a 9/16" diameter body and a tapered down thread diameter of 7/16"Use with Nylon BushingUse as Dry Shackle Bolt or Equalizer Center BoltDiameter of Bolt Body: 9/16"Length of Bolt: 3"Diameter of Threads: 7/16"Use with Flanged Lock...$4.45 -
Buyers
90115 --- Stainless Steel Document Holder
Tube Diameter: 1.5" CapKeeper Protective Cable Secures Caps to Mounting Bracket Mounting Bracket Dimensions: 5-3/4" high, 2-13/16" wide x 4" deep Mounting Bracket Features Cushioned Tube Supports & Pre-Drilled Mounting Holes Patented Rubber Caps...$20.95 -
Croft
AH4 --- CROFT Adjustable Coupler with N-3 Loop Nut - 12,000lb Capacity - 2-5/16"
The CROFT Original. Adjustable couplers offer the flexibility of changing the coupler height to match multiple towing vehicles. This adjustable coupler is safe, rugged and simple to operate. Its body and lip are constructed of high grade cast steel and...$76.95 -
Peterson
421R --- Oval Sealed Tail Light
This oval light may be used on either curbside or roadside of trailer and can be mounted horizontally or vertically.Oval Sealed LightColor: RedFunctions as Stop, Turn, and Tail LightLength: 6-1/2"Height: 2-1/4"Depth: 2-3/8"Made in the USA$9.45 -
RAM
RAM151101 --- RAM Swivel Sidewind Trailer Jack - 2,000 lb
This RAM jack swivels into four different positions by pulling an easy grip pin. Maximum Support Capacity: 3,000 lb Maximum Lift Capacity: 2,000 lb Handle Style: Sidewind Travel: 10" Retracted Height: 10.8" (Measured from Center of Mounting Bracket)...$49.95 -
Demco
12397 --- Demco Rue Ring Lock Cotter Pin - 7/8"
Rue Ring Locking Cotter Pin Fits 7/8" diameter pin DA91 and DA91BZ actuators requires one DA10 and DA20 actuators require two$3.95 -
Peterson
540 --- Trailer Light Kit
This kit contains all legal lighting and reflectors required for trailers under 80" wide. Square Trailer Light Kit - Under 80" Wide TrailerMade in the USA Following Parts are included in the kit One Red Left Tail Light with License Illuminator, Part...$35.95 -
Peterson
146-18 --- Peterson 2" Round Flush Mount Grommet
Peterson Grommet for 146 series LED and Incandescent Clearance and Side Marker Lights Use with LED143A, LED143R, 143A and 143R Flush Mounts 2" Round Style Lights in a 2-1/4" Hole Requires a 2.25" Round Hole for mounting in panel with maximum thickness...$1.45 -
BULLDOG
150415 --- BULLDOG Swivel Sidewind Trailer Jack - 2,000 lb
BULLDOG sets the standard for round screw jacks. They operate smoothly and efficiently with easy cranking 8 turns per inch. There is no better, more reliable, field proven jack on the market. With four 90 Degree quick positions, secured by a convenient...$109.95 -
RAM
RAM4BWC --- RAM Adjustable Coupler - 12,500 lb Capacity - 2-5/16"
These sleeve Lock couplers come with a precision angle shaped self adjusting cast head for easy hooking and unhooking. Adjustable couplers include grade 8 bolts and nuts and work with industry standard 3" channel. Sleeve Lock couplers come with black...$59.95 -
Dexter Marine
18078 --- Adjustable Clevis Hitch - 20,000 lb Capacity
Designed to meet the need for an adjustable clevis hitch. Clevis Hole: 1" Vertical Hole Spacing: 2" center to center Attachment Hole Size: 5/8" Fits into a 3" channel Clevis Pin, Channel & Hardware Sold Separately Capacity: 20,000 lb$54.95 -
Fastway Trailer Products
Z2140 --- Fastway Zip Breakaway Cable - 4'
The Fastway, Zip breakaway cable is designed not to drag. It keeps the cable up off the ground and out of harms way while you are towing and when you are not towing. The cable easily attaches to an existing pin and snap hook attaches to your hitch. ...$16.95 -
Peterson
143A --- Round 2-1/2" Sealed Clearance/Side Marker Light
This light features a lens welded to the housing to form a single unit. Also includes 15,000 hour long life bulb.2-1/2" Round Sealed LightColor: AmberFunctions as Clearance/Side MarkerIncludes 15,000 Hour Long-Life BulbDiameter: 2-1/2"Depth: 3/4"Made in...$5.45 -
Dexter
5-101 --- EZ Lube Washer (Before 2002)
Includes Two Fold over Tabs for Locking the Spindle Nut to the Spindle Fits One Inch Diameter EZ Lube Spindles Can be used with most One Inch Spindle Castle Nuts$1.45