$42.95
$7.45
$6.45
$10.45
$13.95
$13.45
$5.95
$19.95
$3.45
$59.95
$15.95
$31.95
$28.95
$53.95
$15.95
$36.95
$23.95
$56.95
$14.95
$23.95
$8.95
$23.95
$11.45
$36.95
$50.95
$26.95
$10.45
$7.45
$11.45
$15.95
$4.45
$52.95
$134.95
$14.95
$13.95
$7.45
$6.45
$12.45
$11.45
$36.95
$23.95
$8.45
$18.95
$13.95
$8.95
$13.95
$36.95
$8.45
$9.95
$34.95
$5.45
$182.95
-
RAM
15181 --- Replacement Handle & Clip
Dropleg Jack Handle Fits 1" shaft From edge of bracket that holds the bolts to vertical is 5.5" Vertical is 13" Last bend to end of handle is 7.5"Add to Cart$42.95 -
RAM
15273 --- Replacement Round Weld On Mounting Tube - 9/16" Pin Hole
Weld-On Round Jack Tube. Male Mount - Fits Inside Jack Mounting Tube Use with 9/16" Pin and Chain, Part No. 018403 Weld Mounting Tube on to Trailer Tongue pinhole Diameter: 9/16" Outer Diameter of Tube: 2" Length of Tube: 1 7/8"Add to Cart$7.45 -
BULLDOG
15500 --- BULLDOG Replacement Sidewind Tube Cap
Jack Tube cover.Replacement Tube CoverDiameter: 2"Add to Cart$6.45 -
BULLDOG
15909 --- Replacement Mounting Bracket
Jack Mounting Bracket Use with 1/2" Plunger Pin, Part No. 18400 Weld Bracket on to Trailer Tongue Pin hole Diameter: 1/2" Snap Ring not included, Part No. 18405Add to Cart$10.45 -
BULLDOG
18400 --- Replacement 1/2" Plunger Pin Assembly
Use with Mounting Bracket, Part No. 015909 Plunger Pin Diameter: 1/2"Add to Cart$13.95 -
18403 --- Replacement 9/16" Pin and Chain
Usable Length: 4" Overall Length: 4-1/2" Diameter: 9/16" Use with Mounting Tube, Part No. 15273Add to Cart$13.45 -
BULLDOG
18405 --- Replacement Snap Ring, .079 Thick
Ring Thickness: .079 inches Use with 80580 and 15909 Mounting Brackets Inside Diameter: 2.25" Will not fit RAM12MBAdd to Cart$5.95 -
Add to Cart$19.95 -
22132 --- Safety Pin 3/8" x 2-1/4"
Snap Lock pin Zinc Plated Square Wire Lock Diameter: 3/8" Usable Length: 2-1/4" Shank Length: 2-3/4" Overall Length: 3"Add to Cart$3.45 -
Andersen Manufacturing
3604 --- Camper Leveler and Chock
The Camper Leveler is the perfect trailer leveler. Simply place a Camper Leveler under the low-side tire and drive up until you reach level, then place the attached chock under Camper Leveler to maintain level status. Each kit includes a leveler and...Add to Cart$59.95 -
BULLDOG
500106 --- Bevel Gear Kit for BULLDOG Jack
Replacement Gear KitOuter Diameter of Gears: 1.37"Inner Diameter of Gears: .5"Thickness of Gears: .705Teeth per Gear: 15Both gear are identicalKit includes two gears and two roll pinsAdd to Cart$15.95 -
Add to Cart$31.95 -
Add to Cart$28.95 -
BULLDOG
500190 --- Steel Jack Drop Leg, Fits 2" O.D. Inner Tube
This Drop Leg Foot is ideal to use with your A-Frame or Tube Jack for additional adjustable height and trailer stability. ONLY fits the following Jacks: 150052, 155157 and 155022 5.278" Round Foot 5 Holes on 1.5" Increments Raises Jack a total of 9-1/2"...Add to Cart$53.95 -
BULLDOG
500223 --- Top Bearing for BULLDOG Jacks
Top Bearing or Thrust Bearing Inner Diameter: .5" Outer Diameter: 1.26" Thickness: .43"Add to Cart$15.95 -
BULLDOG
500256 --- Replacement Handle & Gear Kit
Includes 2 Gears, 1 Solid Pin, 2 Gear Miters, 1 Grooved Pin & Handle. Diameter of Handle: 1/2" Center of Pin hole to end of handle: 2-1/8" Length of handle: 5-5/8"Add to Cart$36.95 -
Add to Cart$23.95 -
Fulton
500320 --- FULTON XP to F2 Jack Adpater Kit
This Fulton part allows a F2 Jack to fit onto an XP bracket. Allow consumers to upgrade from a Fulton Center-Bolt Swivel Mount Jack to an F2 Jack w/4" frame Fits Fulton's patented center-bolt design - used on XP10 and XP15 weld-on jacks Maintains the...Add to Cart$56.95 -
RAM
5024 --- Replacement Round Weld On Mounting Tube
Female Mount - Fits Outside Jack Mounting Tube Inner Diameter of Tube: 2.5" Use with 5/8" Pin and Chain, Part No. 700026 Weld Mounting Tube on to Trailer Tongue Length of Tube: 2.5" Pin Hole Diameter: 5/8"Add to Cart$14.95 -
Fulton
6811S00 --- 6" Replacement Wheel
This Fulton Caster Repair kit includes a 6" wheel, spacer split tube, cap screw and Locknut - everything needed to replace the caster.Please call for more detailsAdd to Cart$23.95 -
RAM
700026 --- Replacement 5/8" Pin and Chain
Pin & Chain Diameter: 5/8" Overall Length: 3-7/8" Usable Length: 3" Use with Mounting Tube, Part No. 81271 and 5024Add to Cart$8.95 -
BULLDOG
700056 --- Replacement BULLDOG Sidewind Jack Handle Kit
Includes Handle. Diameter of Handle: 1/2" Center of Pin hole to end of handle: 2-1/2" Length of handle: 6-1/4"Add to Cart$23.95 -
RAM
700263 --- Replacement 9/16" Drop Leg Pin, Chain and Lynch Pin
Drop Leg Pin Diameter: 9/16" Overall Length: 4-7/8" Usable Length: 3-3/4" Includes Lynch Pin to secure 9/16" Pin Drop Leg Pin Diameter: 9/16" Overall Length: 4-7/8" Usable Length: 3-3/4" Includes Lynch Pin to secure 9/16" PinAdd to Cart$11.45 -
RAM
701340 --- Replacement 2" Square Dropleg Tube
Dropleg Tube. Silver Zinc Plated 2" x 2" Square Tube 6" x 8" Square Foot 700263 Replacement Pin & Chain not included Five Vertical Adjustment Holes on 3 3/8" CentersAdd to Cart$36.95 -
Add to Cart$50.95 -
Pro™ Series
80552 --- Duraplas Wheel Caster, 6" x 2", Fits 2" O.D. Inner Tube
This Jack Caster is ideal to use with your A-Frame or Tube Jack for added trailer mobility. Wheel Width: 2" Wheel Diameter: 6" Jack Inner Tube Fits Inside Caster Attachment Tube Raises Jack 7" Fits jacks with 2" O.D. Inner Tube Wheel Width: 2" Wheel...Add to Cart$26.95 -
BULLDOG
80580 --- Mounting Bracket
Jack Mounting Bracket Pinhole Diameter: 3/8" Weld Bracket on to Trailer Tongue Replacement 3/8" Plunger Pin is not available Use with Snap Ring, Part No. 18405 Snap Ring not IncludedAdd to Cart$10.45 -
RAM
81271 --- Replacement Round Weld On Mounting Tube - 5/8" Pin Hole
Weld-On Round Jack Tube. Outer Diameter of Tube: 2" Male Mount - Fits Inside Jack Mounting Tube Use with 5/8" Pin and Chain, Part No. 700026 Weld Mounting Tube on to Trailer Tongue pinhole Diameter: 5/8" Length of Tube: 2"Add to Cart$7.45 -
Pro™ Series
82650 --- Steel Jack Foot, Fits 2" O.D. Inner Tube - Zinc
This Jack Foot is ideal to use with your A-Frame or Tube Jack for added trailer stability. Fits jacks with 2" O.D. Inner Tube Includes Safety Pin to Attach Foot to Jack Jack Inner Tube Fits Inside Foot Attachment Tube Maximum Capacity: 5,000 lb Finish:...Add to Cart$11.45 -
RAM
82660 --- Extended Steel Jack Foot 8", Fits Jacks with 2" O.D. Inner Tube
This Jack Foot with Extension is ideal to use with your A-Frame or Tube Jack for added height and trailer stability. Fits jacks with 2" O.D. Inner Tube Includes Pin and Clip to Attach Foot Extension to Jack Jack Inner Tube Fits Inside Foot Attachment...Add to Cart$15.95 -
RAM
83670 --- Bottom Support Plate, Fits Jack with 2-1/4" O.D. Outer Tube
Weld Bottom Support Plate to Underside of A-Frame Hole Diameter: 2.29"Add to Cart$4.45 -
Fastway Trailer Products
AJF6500 --- The Fastway Flip Jack
Tired of hauling around and stacking up old 2x4s, just so you can get a little more height from your jack? The new Fastway Flip takes care of those hassles for good. The Fastway Flip jack foot adds six inches automatically to your 2¼" jack ( 2" O...Add to Cart$52.95 -
EZJACK --- EZ Jack
The EZ Jack was designed as an easy to use, safe and reliable device for changing tires on tandem axle trailers. Its unique rocker shape allows trailer operators to simply drive the trailer onto the tire to change. No need for jacks or wooden bLocks. The...Add to Cart$134.95 -
Fulton
P9012-00 --- FULTON Weld-On Mounting Bracket
Weld-On mounting bracket for Fulton swivel jacks. The P9012-00 is a weld on bracket Includes bracket with center bolt, bushing, and Lock nut Bolts for attaching to the frame are NOT included Works with 154107 and XP series jacks Finish: PlainAdd to Cart$14.95 -
RAM
RAM12MB --- RAM Replacement Mounting Bracket
Mounting Bracket for RAM Jacks Use with 1/2" Plunger Pin, Part No. RAM12P Weld Bracket on to Trailer Tongue Pinhole Diameter: 1/2" Snap Ring not included, Part No. RAM12SRAdd to Cart$13.95 -
RAM
RAM12P --- RAM Replacement 1/2" Plunger Pin Assembly
Replacement Plunger Pin for Jack Mounting Brackets Plunger Pin Diameter: 1/2"Add to Cart$7.45 -
RAM
RAM12SR --- RAM Replacement Snap Ring, .103 Thick
Replacement Snap Ring on RAM Jacks Ring Thickness: .103 inches Use with mounting bracket part number: RAM12MB Inside Diameter: 2.25"Add to Cart$6.45 -
RAM
RAM1500JH --- RAM Replacement Sidewind Handle
Replacement Jack Handle for RAM JacK. Includes Handle and Roll Pin Sidewind Jack Handle Diameter of Handle Material: 1/2" Diameter of Roll pinhole: 1/8" Edge of Roll pinhole to end of Handle: 2" Length of handle (center to center): 5-3/4"Add to Cart$12.45 -
RAM
RAM2000JH --- RAM Replacement Sidewind Handle
Replacement Jack Handle for RAM JacK. Includes Handle and Roll Pin Sidewind Jack Handle Diameter of Handle Material: 1/2" Diameter of roll pinhole: 3/16" Edge of roll pinhole to end of handle: 2-1/8" Length of handle (center to center): 5-3/4"Add to Cart$11.45 -
RAM
RAM2500FT --- Replacement 1.75" Square Dropleg Tube
Dropleg Tube ONLY fits RAM2500 dropleg jack. Silver Zinc Plated 1.75" x 1.75" Square Tube 7.5" x 3.75" Square Foot 700263 Replacement Pin & Chain not included Five Vertical Adjustment Holes on 3 3/8" CentersAdd to Cart$36.95 -
RAM
RAM3500JH --- RAM Replacement Handle for RAM Power Jack
RAM Power Jack Handle. RAM Power Jack Override Handle Only fits RAM3500E-L, (EJ-3508 models) Handle has a six sided hexgonal end for attaching to the jacks manual drive Must remove level on top of jack to access the manual drive Socket on the end...Add to Cart$23.95 -
Add to Cart$8.45 -
Add to Cart$18.95 -
Add to Cart$13.95 -
RAM
RAM7TB --- Top Bearing for RAM Topwind Jacks 5k-8k
Top Bearing or Thrust Bearing Outer Diameter: 1.53" Inner Diameter: .75" Thickness: .56"Add to Cart$8.95 -
RAM
RAM7TJH --- RAM Replacement Topwind Handle Kit
Replacement Handle for RAM Topwind Jacks Includes handle, 5/16" bolt, Lock nut and washer Length of Handle: 8.5" (center of pin to center of knob) Fits on onto 3/4" diameter shaftAdd to Cart$13.95 -
Add to Cart$36.95 -
Add to Cart$8.45 -
RAM
SSJH --- Stabilizer Scissor Jack Handle only
Handle only for SSJ424 Overall Length: 27.5" Socket fits a 3/4" nutAdd to Cart$9.95 -
TC48000 --- Replacement Top Cap for 4.5" Square Jacks
Square Replacement Top Cap Inner Dimensions: 4.5" x 4.5"Add to Cart$34.95 -
Fulton
TJ1000TC --- FULTON Replacement Sidewind Top Cap
Fits Fulton Sidewind Jack TJ1000Diameter: 1-3/4"Add to Cart$5.45 -
Croft
TJWK20-SFF --- Croft Flat-Free Wheel Kit with Swivel Feature
This flat-free wheel kit will allow you to move your single axle trailer tongue in any direction without binding. It will aid in getting a single axle trailer moved into just the right spot. This wheel kit is a popular item for man lifts. Includes...Add to Cart$182.95
